The Best Way To Shave With A Safety Razor

The Best Way To Shave With A Safety Razor

Step 1: Pre-Shave Routine
I can’t emphasize doing a pre-shave routine enough. But, what does this mean? For one thing, you possibly can take a hot shower, which makes your hair soft. In the event you don’t need to shower, you should utilize a wet towel. The way I do it's I just make a towel wet, put it within the microwave for a minute to make it sizzling, put it on my face, and let it relaxation there. It’s very comforting, but it surely also helps my hair to get soft. If that’s too much time for you, you can too splash your face with scorching water for a minute or two, until you possibly can really feel that your hair is getting soft.

Step 2: Apply Shaving Cream
Applying shaving cream or shaving lather to your face is next. If you happen to’re in a rush, I suggest you get shaving cream from a tube. Never use cream from aerosol cans, because these products don’t have sufficient fats (which is a natural lubricant). You may also use a shaving cleaning soap, however you’ll need a brush to lather it up and it takes a bit more time.

That being said, utilizing the shaving brush is probably one of the best approach general, because it puts the lather throughout each hair. It also might aid in moving your hair slightly away from your face, which makes the shave easier. Once you’ve bought the shaving cream or a lather in your face, it’s time to truly shave.

Step three: Begin Shaving, With the Grain
At this point, load up your razor’s head together with your blade of alternative, and make sure it’s straight and not crooked (because you don’t wish to cut yourself). Begin the primary pass; don’t fear about removing all of your hair, as a second and (optional) third pass will provide a perfectly smooth result. If you end up just starting out, I always counsel to stand in entrance of the mirror and look at the growth directions of your beard hair earlier than you even begin shaving or lathering up. If you can’t keep in mind how your beard grows, use a pen and paper to diagram the directions you think your hair is growing. Actually, it’s very simple. Just have a look at it closely and also you’ll see it.

Why is it vital to do this, you ask? Well, within the first pass, you need to shave within the direction of your hair grain (or "with the grain"), which is far less hectic in your skin. Truthfully, every man has a slightly different progress direction, so it’s hard to make blanket statements. Personally, I’ve memorized my development directions, so I know exactly in what way I've to shave.

Whenever you make a pass, always be sure that your skin is tight or stretched because if there’s loose skin, you’re a lot more prone to cut yourself. I always use my free left hand to stretch my skin just within the area the place I’m going to shave next. For example, that can imply pulling round your sideburn or reaching overhead to tug up, to tighten the world just earlier than the razor blade goes over it. Sometimes round your cheeks, you too can just puff them out with sufficient air to make the skin tight. Within the area below your nostril and around your mouth, you may also tighten your skin with your muscle tissues, or just use your tongue from the inside.

epending on the head of your double-edged razor, you should hold your handle at an angle of about 30 to 45 degrees. You’ll hear what the best angle is when you do the pass. If you do the pass, you need to be very mild on the skin. Don’t have any robust pressure, just use gravity to slide the razor down in your face. Make sure that you make quick and slow strokes. Whenever you start, ensure you shave in straight strokes perpendicular to the edge of the blade; that way you’re less prone to reduce yourself. When you’re just a little more advanced, You can also have a slight stride; which means you go at a slight angle, because this form of movement creates a stronger cutting motion.

Alternatively, you possibly can get a deal with that is slightly angled, so when you pull down your handle straight it always cuts the hair at an angle, due to this fact enhancing the chopping motion just like on a guillotine. Frankly, I only suggest those angled heads for people with very thick hair, because it makes for a more aggressive razor; when you have just very thin beard hair, you continue to get the same end result with a less aggressive razor, and your skin will thanks for it.

When you’re performed with one or two strokes, just swap to the opposite side of the blade, and repeat once or twice.

Step four: Rinse the Blade After Utilizing Every Side
You can both do this under running water or in a sink that’s stuffed with water. If you really feel any form of pulling or any pain once you shave with a DE razor, it either implies that you didn’t do a proper pre-shave routine, or that your blade is dull.

If you happen to use shaving cream, you'll be able to clearly see where you’ve already shaved. Personally, I wish to have a little bit bit of extra shaving cream in my free hand, so I can apply it after each pass. You may’t have an excessive amount of shaving cream on your skin once you shave, because the cream protects and lubricates the skin. To start with, it could be tempting to go over the identical area three or four occasions without reapplying shaving cream; but trust me, it’s higher to have new shaving cream applied each time earlier than you shave.

That being said, if you’re just learning a way; everything goes to take you a lot longer, and so by the point you make it from your right side to the left side, chances are you'll already experience a drying feeling in your face. Now, you don’t need a dry shaving cream, because it clogs up the razor and prevents skin protection. Due to this fact, when you can really feel that it gets a little bit drier, wet your hand, go over the world again, and maybe reapply somewhat bit of lather or shaving cream so everything is contemporary earlier than you shave over it.

If you have any concerns regarding where and the best ways to use #shavingsoap, you can call us at our website.
   
© Copyright 2013